Project Nissan Datsun Bluebird 910

[nnabeel]

The car body seems perfect. Why not save money on replacing any engine instead getting the one sorted which is installed.

the money saved can be used for refurbishing the dashboard or sourcing a new one, changing some cool rims and other required bits and pieces, interior work, fog lights that suits the car etc etc.

[hassanmughal101]

brother i don't use this bluebird as daily driven just once in week
if swap vq35 it will be heavy for me for now i go with sr20
so what things have to change with sr20 ?
approx. what is the cost of complete setup ?
and i am not know to Nissan community
i am diehard of Nissan/Datsun from last 15 years
and should Recommend Beams for it Because many people from foreign countries
swap BEAMS / 1UZFE / SR20DET / RB25DET / RB26DETT / 1JZGTE OR 2JZ GTE OR N/A

[hassanmughal101]

Can't Find dash for this Bluebird
have to get repaired this one
I have rims with me for Super chrome Works mister s1 16"
also have some carpet for floor
seat are have gone for fresh dark navy blue
HeadLiner its Great Condition

[hassanmughal101]

will have to change the diff ? for sr20
or complete rear end
and front end have to replaced ?

[dani_kk]

Approximately this swap will cost you around 700-800k
Engine cost is around 350k rest, mounts shaft, diff, focus on suspension brakes and alot.

[hassanmughal101]

suspension, brakes ,diffs ,engine ,gear ,wiring,
complete running car all in 700k to 800k ?

[nnabeel]

i guess keeping in view the current conditions, it can go farther than the estimated figures.

better to redo the installed engine as u have to drive it often or once a week.

[dani_kk]

Yes it's just an estimate, it can go beyond 800k with a factor of 100k so you should have 900k with you.

[hassanmughal101]

i should swap beams in it i take help regarding this on Instagram from different 910 owners around the world
i one them has been swaped beams and after beams he swaps a 1uzfe in it with Skyline R31 rear and silvia 13 front with beams he upgraded the suspension to coilovers and welded the diff and install
here's check this out is insta id
https://www.instagram.com/nracerz28/
and suggest me members what to do

[hassanmughal101]

[hassanmughal101]

Hello its Hassan
so i have decided to keep this for now in future we may need some big motor of it then we would upgrade that

[hassanmughal101]

i have kept this engine in my 910 but need help me regarding overhauling it PKW
it not start now i removed the fuel tank for Repainting to Painter who paints bike tanks and and forget about take photo of pipes and the fuel pump has been changed so it don't suck petrol until is half fill what is solution of this ?and should i replace fuel lines ?
and need some parts for it like back lights and should i get it some touchups or not because the car is in its Genuine paint ?

[hassanmughal101]

THIS IS WANT I WANT TO MAKE IT

[nnabeel]

The pipe that sucks fuel from inside maybe broken due to rust. check that.

once i had got repaired tank of 81 corolla, same thing happened while installing back. then i had to make a new pipe so that it reaches till the bottom.

if there are no visible rust or dents, i would suggest dont get touchups. as for lights, find in scrapyards near ur area or if found online.
as per the pictures u posted above, the car body seems perfect as well as the back lights. why u want to change them,

[hassanmughal101]

basically i need lenses of lights mean Covers And i From Sialkot and here is Impossible find lights for this no Scrapyard like Bilal gunj & Sher Sha

[olaluxfashion]

I am trying to find a Datsun 910 for a long time .It was my dad`s ride back alain until we had to scrap it due to Traffic rules and old model .Any idea where i can get one ?

[hassanmughal101]

where your from brother ?

[capsat]

@hassanmughal101 if you post picture of rear light @nnabeel can guide you for refurbishing of the same.

[hassanmughal101]

[hassanmughal101]

this is rear light picture and upper chrome has been bend and plastic is faded how it can restored ? @nnabeel @capsat